北京精时恒达钟表有限公司

　　精时恒达手表全国连锁维修点(请选择您就近的维修点咨询售后事宜)

　　精时恒达名表连公司成立于2001年是一家专注于手表维修的现代化大型服务型企业。公司总部位于北京，在全国各大中型城市设有维修服务中心，形成了庞大的手表售后维修服务网络，为广大消费者提供方便、快捷的手表维修服务!

　　【精时恒达手表售后维修中心门店图】

　　【图为：手表抛光工作台】

　　【上图为：手表做真空、压缩、冷凝及防水测试的设备】

　　在检查瑞士名表的外观零件的时候，**主要检查的表壳应该没有砂眼和明显的划痕，各棱角对称并且后盖与上壳的旋合处应严密两只表环各与表壳的距离相等，安装耳璜的孔应该在表壳脚尾部的位置居中不偏，孔的深度适当，使表环不易脱落表镜应没有疵点和划痕，透明光亮三针安装正确，针与针、表镜与表盘之间应有正确的安全间隙表盘和指针镀层光洁度好，没有斑痕，表盘刻度线条或夜光点完整等相关事项。

　　1检查名表的灵敏度

　　2把还没有上过发条已经停止走动的手表轻轻地摇动一下，借助摇动的力量来观察秒针走动的情况：如果秒针在很短时间内就停止走动，则说明这只手表上足发条后能全部走完(即发条无力矩)，灵敏度高如果秒针长时间继续走动，则说明这只手表上足发条后不能全部走完(即发条还储存力矩)，灵敏度不高或表机有故障。

　　3将还没有上过发条停止走动的手表，慢慢地转动把头，观察秒针起动情况：上条把的转动越少，秒针起动越早的说明该表的灵敏度越高反之则灵敏度低或表机有其他故障。但要注意快摆手表由于游丝的刚度较大，要比传统频率(18000次/小时)的手表要多上一点发条才能起摆。灵敏度高的手表，上足一次发条后延续走动的时间较长。

　　4检查名表指针的间距和位置：表针与表镜、表盘之间以及三针之间都应该保持一定的间距，否则相互产生碰擦而影响表机的正常运转。检查时可通过拨针观察。时针和分针的位置和相互配合是否正常的检查方法是：将分针和时针拨到3点、9点，观察两针是否成直角拨到6点，两针是否成直线拨到12点，两针是否重合。

　　5检查名表上条机构：正常的手表上条应是轻松的。转动把头上条时，先觉得较松，渐渐地越上越紧，当不能继续向前转动把头时，说明发条已完全上满和上条机构工作正常。如果转动柄头上条时，发生“喳喳?的异常响声，或者产生顶齿打滑等现象，则说明上条机构有故障。

in the examination of the Swiss watch appearance parts, the main check case there should be no voids and obvious scratches, the edges and corners of symmetry and the rear cover and the upper shell screw should be tight and the two table ring distance case, installation holes should be in the case of ear Juan foot tail position center is not biased, the depth of the hole is appropriate, the ring is not easy to fall off the table mirror there should be no defects and scratches, transparent bright three pin is installed correctly, the needles, table between the mirror and the dial should have the right security clearance dial and pointer coating finish, no spots, lines or luminous dial scale point and other related matters.

1 check watches

2 haven't had a clockwork watch has stopped walking and gently shake hands with the move to observe shaking force: if the second hand in a very short period of time to stop walking, then this watch is wound up after the finish (i.e. a torque free), if the second high sensitivity long time to walk, then this watch is wound up after not finish (i.e. a storage torque), the sensitivity is not high or table machine failure.

3 will have not been stopped a watch, slowly rotating head to observe the second start: the article to turn less, second hand start the sooner the sensitivity of the table is high and low sensitivity or other fault table machine. But it should be noted that due to fast pendulum watch gossamer stiffness greater than traditional frequency (18000 times / h) to a little wind to put the watch. The high sensitivity of the watch, the first time after the foot of a spring to continue to move around a longer time.

4 check watches pointer: between a hand and the table mirror dial and three pin should maintain a certain distance from each other or rubbed and affect the normal operation of the machine table. Check can be observed through the dial. The hour and minute hand position and cooperate with each other to check whether the method is normal: the minute and hour hand to 3 points, 9 points, to observe whether the two pins at right angles to dial 6, whether the two pins into a straight line dial to 12 points, whether the coincidence of the two needles.

5 A: normal check watches watch section should be easy. When turning the head, first feel loose, gradually more and more tight, when you can not continue to move forward when the head, the spring has been fully on the full body and the work of the body. If you turn the handle head bar, "Cha abnormal noise, or tooth slippage phenomenon, then a failure mechanism.

精时恒达全国连锁维修：400-875-1181全国百家连锁，**名表维修**，服务地区：北京 、上海、广州、杭州、深圳、沈阳、南京、太原、成都、 天津、 南昌 、武汉 、、等等